Powerhead vs. String Trimmer

Clearing up lawns can be quite a challenge, especially if you don’t have the right tools. String trimmers have always been a staple when it comes to cutting grass, weeds, and other plants that may cause your garden to look less neat than usual. However, one product is fast becoming a worthy challenger to the string trimmer. This is none other than the Powerhead. Is this product from Ego the type of cutting tool that you need? More importantly, is it actually better than your standard string trimmer? This comparison will answer those questions and more.

To start things off, it would be nice to take a closer look at the Powerhead trimmer. At first glance, you can see right away that the Powerhead is slightly bigger than the usual 15-inch string trimmer. This gives off the immediate impression that this product is better equipped for heavy-duty cutting. On closer inspection, the Powerhead also has a larger reload head and a wider, deeper guard. The Powerhead houses a 2000-watt motor, which gives it more than enough power for trimming the lawn. Aside from the grass cutter, the Powerhead also comes with other attachments such as the edger and the chainsaw.

On paper, one can see that the Powerhead is a completely different animal compared to the usual string trimmer. On the next part of this article, we will compare how both of these tools perform and see if a clear winner can be picked between the two.

Performance– On the performance side of things, the larger motor of the Powerhead means it can cut through tougher grass much easier compared to your usual string trimmer. The larger dimensions of the head also make it more resistant to tangles, which can help in quickening the pace of your cutting. However, the immense power of the Powerhead may prove to be a disadvantage for some, as its motor can be quite difficult to handle at full throttle.

Control– This is one of the more distinct advantages of the trusty string trimmer. Handling its power is a much easier task compared to using the Powerhead. At the same time, the smaller, lighter head of the string trimmer makes it much easier to use. This is especially so when you are maneuvering around the tight spaces in your lawn. The Powerhead is still controllable in spite of these things, but you’ll need to get used to its power and weight.

Value– In terms of value, it all depends on what you need in a grass cutter. The string trimmer has more than enough performance to get the job done right on most occasions. However, if you are looking for something more suited for heavy-duty use, then you might want to consider the Powerhead. The Powerhead can also be converted for other uses, but that might not matter if you’re just looking for something to trim your lawn.

At the end of the day, you can’t go wrong with going for either device. The Powerhead has better performance, but the string trimmer is more user-friendly. Choose the unit you think you’ll be more comfortable using.

How to Change a Spool on Weed Eater

One of the greatest and most useful tools for you to keep or maintain the cleanliness and beauty of your garden is a weed eater. Through the use of a specific type of weed eater, you can trim your yard and make around its edges very neatly. However, it is quite unfortunate to say that a plastic cording may only lasts longer in a spool prior to alter it.

If that happens to the tool that you are utilizing, it is essential to change or alter first the spool of its monofilament. Try to keep in touch on the succeeding discussions for these will be your guide on proper maintenance of string trimmer or weed eater that you have.

If you have the eagerness and perseverance to look for the proper ways and approaches on how to change a spool on the monofilament of your weed eater, then try to refer on the following lists and steps as your guide:

  1. If it is an electric type of weed eater, then you need to unplug it for safety purpose. If the model that you have is a gas trimmer type, then it is essential to get rid of the spark plug of it.
  2. Tilt the model or the unit so that you can properly have an easy access to the monofilament’s spool. Then, try to unscrew the cap based on the directions which were shown in the model of your tool. The next thing that you need to do is to pull off the spool from the weed eater. Clean first any debris or grass from its head if there is any.
  3. Unroll the replacement line of the weed eater from the spool of the replacement. It must be approximately 30 ft for great convenience and assurance that you can achieve best results. Also, you need to make sure that you have measured the correct diameter of your weed eater.
  4. Insert at least 1-inch of the line’s weed eater into the middle of your weed eater’s spool. Then, wrap the line of the weed eater snugly onto the spool of it. Make sure that you wrap it according to the direction of the spool’s arrow.
  5. Run the weed eater cord’s tail out through its feedhole. Put the spool of the monofilament back to the weed eater. Make sure that you put it back with 4-6 inches of tail that extends from the tool. Tighten the cap of it to make sure that it will be back in its place.
  6. Plug in the weed eater if it’s electric type or put the spark plug back on your weed eater if it’s a gas trimmer type. Then, you may now continue trimming grasses and weeds. You may probably need to tap its ground unit to properly feed it. If it does not, then, disconnect the source of your power and re-check if the line is feeding properly through its feed hole.

With these step-by-step procedures, you can now successfully change the spool of the weed eater’s monofilament and continue your gardening works for good. You will no longer find any difficulty in doing your gardening tasks since you have already the knowledge on how to maintain the longevity of your gardening tool – weed eater.

If you want more details and information about the proper and additional ways of prolonging the lifespan of your tool, then try to read more buying guide online. There are some online sites that provide great and useful information about this matter.

Electric Bike Route Planner

In this tutorial I will show you how to calculate the distance from your home (or any other point) to destinations you might like to ride your electric bicycle to. You can find out how far it is from your home to your office or favorite restaurant via trail or road. This is a great way to plan your route to avoid high traffic areas also.

You’ll be surprised how many places you can get to and back with your electric bicycle. My bike gets about twenty miles per charge so I figure about 9 miles each way to be safe. I never really thought about it before I started ridding my electric bicycle, but almost all the places I go on a daily basis are within 9 miles of my house. All those years of starting up the car just to go a couple of miles was really wasteful and the gas used adds up fast and is really unnecessary.
The health benefits of electric bikes are great because *you will ride everyday* not just when the conditions are perfect outside whereas you probably don’t ride everyday on your non electric bicycle (right?).

O.K. on to the tutorial. This method works better than using other mapping applications because you can choose which streets and or paths, bike trails etc… that you want to take. And choosing back roads or secondary streets rather than busy roads that the other applications usually point you to. This is especially good for electric bikes, but can be used effectively for any electric vehicle.

If You don’t have Google Earth already installed you can get it here for free.

Open up Google Earth, type in your home address and put a pin in your roof. Select the push pen icon at top and move it to your starting location, give it a name and OK. Now select the Ruler tool in the tool bar. Choose Path in the fly out and select Miles. Begin your line by clicking once in the street in front of your house, then go to the point where you will turn and click. Continue the line until you are at your destination then give the route a name and save it. That’s it! You can make as many routes as you like to all your favorite destinations and know that you’ll have plenty of juice to get back home.

Choosing the Best Exercising Bike

In the U.S. practically all fitness gyms have their own set of exercise bikes and people often use them regularly. This type of equipment is very popular for many decades now probably because of the simplicity and ease of use for the machine yet giving you a really great cardiovascular workout.

You may be more familiar with the upright type of bike as it’s the most common but there’s actually another type of bike which is called as the recumbent bike. The upright bike is just like a regular bike but is made stationary and is either missing 1 wheel or even both wheels.

Choosing the Best Exercising Bike

The recumbent bike is very different and may seem strange to you at first as you are actually lying down and you are going to put your feet on the pedal that is in front of you.

There’s actually another kind of exercise machine that somehow falls into this category and it’s the bike trainer. It’s actually just a stand where you put a real bike in and it lifts its rear wheel and makes it stable. You can even add resistance to the rear wheel and that’s what will give you a more powerful workout. It pays to get a great bike trainer as it can handle even the fastest pedaling of a biker. This is a great idea for those who are already comfortable with their own bike and want to use it both indoors and outdoors for their workout.

If you have already decided whether you’d go for the upright bike, the recumbent bike or the bike trainer, you should then choose what model you’d want by checking the features being offered. There are different features you should look for and the most useful are usually the electronic display and the heart rate monitor.

The heart rate monitor must be interactive and gives you your pulse rate and it adjusts the intensity of the workout based on that while making sure that you are getting the most from your workout. This means that you no longer have to constantly monitor your own heart rate and make the necessary adjustments to keep your heart rate at the optimum level and not go over or below it.

Electronic display on bike machines must be readable and clear and lets you manually adjust it even while you continue to pedal your way to fitness.

how to Prepare Your Hot Tub for the Winter

Hot tub is an important addition in our homes. During winter many people take a break from using a hot tub. If you want your water tub to last for long one should take of it. One way is always keep hot tub clean. If water freezes after being left for long it can cause hot tub to crack. This is how one prepares hot tub for the winter.

1: Power turn off. The first thing one should do is make sure your water tub’s power and heater is off. This is so that maintenance can be done fully.

2: Rinse the hot tub: Rinsing it helps to remove body oils that has been building up affecting the jet and pipes.

3: Empty the hot tub: One should make sure all the water from the hot tub is removed. If water freezes after being left for long the hot tub cracks. It is very costly to repair a crack.

4: Drain the air blowers: Not all hot tubs have the air blowers. If yours have it. One should switch off power and remove the heater. Heater get damaged when it runs without water. Then switch on the power and let the hot tub run for about 30 seconds before switching the power off. This will remove all the water from air channels of the hot tub.

5: Degrease your filters: Remove all filters and their baskets. Use clean water to clean both filters and baskets.

6: Loosen fittings: One can open hot tub cabinet, look for pipes connected to pumps and loosen them. This helps in draining water in pipes.

7: Blow out the pipes: The remaining water from jet piping is removed by blowing end by air compressor. Do this from one jet to the other. Make sure all water from jet system is out.

8: Remove water: Remove water that that came from pipes while you were blowing them. Ensure the hot tub is completely dry. One can use shop-vac, sump pump or sponge.

9: Rinse and dry the hot tub: Clean the hot tub using hot tub cleaner and rinse it.

10: Cover the hot tub: You cannot get tired trying to prepare your hot bath just to leave it open. This the time you take your hot tub cover and cover your hot tub. This is to ensure anyone or anything does not get inside.

11: We are through: After covering the hot tub with the hot tub cover, you are now through with preparing your hot tub for the winter. You can now relax peacefully knowing you are ready for the winter.

Note carefully:  If you are not sure whether you want to prepare your hot tub for winter yourself. You can hire services from professionals. Most companies who offer the service gives guarantee that if the hot tub cracks due to winterization they will fix it for free. Damages that mostly affect hot tubs are caused by improper winterization. You must be extra careful when you decide to do winterization by yourself.

Posted in: Fun

Buying Guide for Full Face Mountain Bike Helmets

The usual mountain bike helmets are open faced cap type helmets that offer protection for the top of the head. These helmets are great for leisure cycling and cross country mountain biking because they are lightweight and they give riders better ventilation. But for those who need more protection, full face mountain bike helmets are the way to go.

Some types of cycling are inherently more prone to serious accidents. For example, down hill, dirt jumping and speed cycling requires aggressive maneuvers that may put riders at greater risk for injuries. For these activities, the better protection that only a full face helmet can provide is preferred.

How do you evaluate full face mountain bike helmets? Here are some pointers.

The point of a full face helmet is getting the best kind of protection there is. There are several types of safety certification for helmets. Here are some of them:

    1. CPSC certification standard. CPSC stands for Consumer Products Safety Certification. This is the basic requirement for all helmets. Certified helmets will have a CPSC sticker inside it.
    2. ASTM F 1952 Downhill Mountain Bike Helmet Standard
    3. ASTM F 2032 BMX Helmet Standard
    4. DOT
    5. Snell

A well fitted helmet will offer more protection than one that fits poorly. Be sure to get a helmet size that’s appropriate for the size of your head. Some helmets have an adjustable fit system which basically allows you to adjust the fit of the helmet by rotating a dial. This is a great feature to make sure your helmet hugs your head properly.

– Buckles and Straps.

Check the straps and the buckle of your helmet and make sure they are well made. You want straps that are easy to adjust and fastens securely. You simply don’t want your helmet to fall loose during critical moments.

Many riders prefer lightweight helmets simply because they are more comfortable.

Aside from choosing a design based on the graphics and colors that you want, you may also want to consider useful design features such as:

    1. a fair number of vents to keep your head cool
    2. an adjustable visor to shield your eyes from the glare of the sun or against stray branches
    3. a good sized eye port that allows you to use your goggles with your helmet
    4. an absorbent liner that can wick sweat away from your face
    5. a liner that can be detached and washed

To further ensure your safety, always inspect your mountain bike before you take it out for a spin. Make this a regular habit to avoid serious injuries.

Easy Upgrade: Reupholster an Office Chair

Your office chair will get old and will become uncomfortable, that is an absolute fact. In addition to that, you may buy a chair that is not perfect for and you tell yourself after a while that you need to buy a new one to meet your needs. But instead of buying a new chair which seems too expensive, you can upgrade your office chair by adding or renewing some features so you can save your money and have a brand new chair again. It is so easy and here are some ideas you can do:

-Lumbar support:
I guess that is the biggest problem. If your back support is bad you will have back pain and discomfort during work especially if you are working sitting in your chair for a long time. The ideal position for the lower spine is when it is arched as our spine normally is not in the straight position. The solution of this problem is the Mackenzie super-role. It is a fascinating tool made only for back support. You put it behind your back and it will get your spine in the right position and distributes pressure in a healthy way. You can also place a pillow and it will work just fine.

-Replacing the old casters with new ones:
The old casters make sliding of the chair on the floor quite difficult in addition to getting the floor scratchy. Changing them with new ones is so easy. The old ones are mostly removed using your hands or sometimes you will just need a screwdriver and the new ones are back onto the chair the same way you removed the old ones. The new casters will make the movement with the chair easier so now you can just slide with your chair within the office smoothly.

-Repair the armrests:
after a while, the armrests get damaged. The padding gets old and torn and it makes the whole chair looks ugly. If the armrest is broken, you can replace it. But if it is only the padding, you can change that with a new fabric.
It is so easy; you will use your screwdriver to get the armrest out of the chair. Remove the old fabric and if it stabilized, use your screwdriver and pillars to remove the stables out. Then cover the armrest with the new fabric, stable it with the stable gun and make sure there are no wrinkles. Finally put your armrest back into the chair the same way you took it off.

Footrest:
Sometimes when you adjust the height of the chair so your elbows are level with your desk, your foot become elevated from the floor. That puts a lot of pressure on your legs and hips and to avoid that you can create a footrest. It can be a pillow or anything simple and it will take a lot of pressure off your body.

-Add more Cushions:
With time, the padding of the cushions get older and then the whole chair becomes uncomfortable. Changing the padding and the covering fabric is easy. Unscrew the screws and detach the seat cushion from the back cushion. Remove the old fabric using pillars. Place the cushion on foam and start marking around it then cut the marked part. Place the foam on the cushion then cover it with the new fabric. Wrap the whole cushion with fabric then stabilize it with the stable gun and make sure there are no wrinkles during stabilization of the fabric. Finally get back the seat cushion and the back cushion together into the chair.

Now with those simple methods, you can easily upgrade your chair both cosmetically and functionally.

When It is Safe To Pull Your Baby In a Bike Trailer or Bike Seat

You may want to ask when your little baby is ready to ride in a bike trailer or sitting at the real bike seat ? Is she ready when she is able to sit up steadily or she has to wait until she is able to walk ? Read through the following article for some opinion from the experts.

Your baby — wearing a helmet — can ride in a bike trailer (those little carts with wheels that you pull behind your bicycle) starting when she’s at least 12 months old. “Before you put your baby in a bike trailer, she must be able to sit up steadily, and she needs to have a helmet that fits properly,” says Howard Reinstein, a pediatrician in Encino, California, and spokesperson for the American Academy of Pediatrics (AAP).

The League of American Bicyclists warns that a rear-mounted bicycle seat (the kind that attaches to your bicycle right behind your seat) make the bike less stable. When you get off the bicycle, the weight of the carrier and your child can cause the bike — and your baby — to topple over.

Bike trailers may be more expensive than rear-mounted bike seats, but they’re safer. They can also be used to carry groceries and other cargo when your child is not with you, and they have a higher resale value, according to the League of American Bicyclists. You can safely load your baby into a trailer by yourself, but to put her in a bike seat safely takes two people (one holding the bike, the other holding the child).

When you purchase a trailer, the League recommends that you look for one that has a ball and socket joint where the bike and trailer meet — this prevents the trailer from tipping over if the bike does. The trailer should also have three- or five-point harness seatbelts. Before every ride make sure to strap your child in securely.

When you choose a helmet for your child, look for a label that says it meets Snell, ANSI, or CPSC safety requirements. The League of American Bicyclists also suggests that you bring your child into a specialty bike shop where a salesperson can help you find a helmet that fits properly. The helmet should fit snugly, meaning it shouldn’t rock back and forth or side to side. The straps should be adjustable so that you can tighten them under your baby’s chin (never leave the helmet straps open or loose). If you can twist or pull the helmet in any direction and it comes off your baby’s head or the buckle loosens, then the helmet won’t be effective protection in an accident.

Your child might be less likely to resist wearing a helmet if you let her choose a color that she likes. Make sure she knows that your policy is “no helmet, no bike ride” — and prove the rule by following it yourself. Wearing helmets can protect you and your baby from serious injuries.